Omron NX1P2 series Скачать руководство пользователя страница 115

Страница: 115 / 264

3-7

Sysmac Studio

This section describes the models and connecting methods of the Sysmac Studio.

3-7-1

Model Numbers

The model numbers of the Sysmac Studio are given in the following table. The model numbers are
different for the media and licenses.

Product

Configuration software

Media

Number of

user licens-

Model

Sysmac Studio
Standard Edition

Sysmac Studio
The following Support Software is also
included.
Network Configurator
CX-Integrator
CX-Protocol
CX-Designer

DVD

---

SYSMAC-SE200D

Licenses

SYSMAC-SE201L

SYSMAC-SE203L

SYSMAC-SE210L

3-7-2

Connection

With an NX1P2 CPU Unit, you can connect the Sysmac Studio online in the following ways.

Configuration

Connection with EtherNet/IP

•

1:1 Connection

•

1:N Connection

EtherNet/IP

Sysmac Studio

EtherNet/IP

Sysmac Studio

•

A direct connection is made from the Sys-
mac Studio. The IP address and connec-

tion device do not need to be specified.

•

You can make the connection whether or
not an Ethernet switch is used.

•

Support for Auto-MDI enables the use of
cross cables or straight cables if a direct
connection is made.

Directly specify the IP address of the remote device.

3 Configuration Units

3-33

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

3-7 Sysmac Studio

3-7-1

Model Numbers

Содержание NX1P2 series









































































































































































































































































Результаты поиска

Содержание NX1P2 series

Отзывы:

Бренды по названию

Популярные бренды

Omron NX1P2 series, Руководство пользователя по оборудованию

Результаты поиска

Содержание NX1P2 series

Отзывы:

Бренды по названию

Популярные бренды