manualshive.com logo in svg

Omron NX1P2 series, Руководство пользователя по оборудованию

Поделиться
Скачать
Omron NX1P2 series Скачать руководство пользователя страница 197

l

Using Ferrules

If you use ferrules, attach the twisted wires to them.
Observe the application instructions for your ferrules for the wire stripping length when attaching
ferrules.
Always use plated one-pin ferrules. Do not use unplated ferrules or two-pin ferrules.

The applicable ferrules, wires, and crimping tools are listed in the following table.

Terminal

types

Manufactur-

er

Ferrule model

*1

Applicable wire

(mm

2

 (AWG))

Crimping tool (applicable wire size given in pa-

rentheses)

All terminals
except
ground ter-
minals

Phoenix
Contact

AI0,25-8

0.25 (#24)

Phoenix Contact

CRIMPFOX 6 (0.25 to 6 mm

2

, AWG24 to 10)

AI0,5-8

0.5 (#20)

AI0,5-10

AI0,75-8

0.75 (#18)

AI0,75-10

AI1,0-8

1.0 (#18)

AI1,0-10

AI1,5-8

1.5 (#16)

AI1,5-10

Ground ter-
minals

AI2,5-8

2.5 (#14)

AI2,5-10

All terminals
except
ground ter-
minals

Weidmuller

H0.14/12

0.14 (#26)

Weidmuller

PZ 6 Roto (0.14 to 6 mm

2

, AWG26 to 10)

H0.25/12

0.25 (#24)

H0.34/12

0.34 (#22)

H0.5/14

0.5 (#20)

H0.5/16

H0.75/14

0.75 (#18)

H0.75/16

H1.0/14

1.0 (#18)

H1.0/16

H1.5/14

1.5 (#16)

H1.5/16

Ground ter-
minals

H2.5/15D

2.5 (#14)

H2.5/16DS

All terminals
except
ground ter-
minals

Wago

FE-0.25-8N

0.25 (#24)

Wago

Variocrimp 4 (0.25 to 4 mm

2

, AWG24 to 12)

FE-0.34-8N

0.34 (#22)

FE-0.5-8N

0.5 (#20)

FE-0.5-10N

FE-0.75-8N

0.75 (#18)

FE-0.75-10N

FE-1.0-8N

1.0 (#18)

FE-1.0-10N

FE-1.5-8N

1.5 (#16)

FE-1.5-10N

Ground ter-
minals

FE-2.5-8N

2.5 (#14)

FE-2.5-10N

*1.

This represents a typical model. Actually, colored codes and other information is added.

When you use any ferrules other than those in the above table, crimp them to the twisted wires so
that the following processed dimensions are achieved.

5 Installation and Wiring

5-53

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

5-4 W

iring

5

5-4-8

 Wiring to the CPU Unit T

erminal Block

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды