Omron NX1P2 series Скачать руководство пользователя страница 143

Страница: 143 / 264

Internal

circuits

NX Unit power supply

NX-series NX1P2

CPU Unit

Built-in I/O

Unwired
terminal

Unit power supply

(24 VDC)

I I_unit2

I_ioB

Cn(+V)/0Vn
terminal
PNP (sourcing)
type only

I/O power supply

(24 VDC, etc.)

End
Cover

I/O power
supply

I/O power
supply
terminal

External devices

I_unit2

I_io1

Unit power supply terminals

I_io2

Additional
I/O Power

Supply

Unit 1

Additional
I/O Power

Supply

Unit 2

Additional

NX Unit

Power

Supply Unit

Unit power supply
terminals

I_unit1

I/O power
supply
terminal

Block that the CPU Unit supplies Unit power supply.

Block that an Additional NX Unit Power Supply
Unit supplies Unit power supply.

Block that an Additional I/O
Power Supply Unit 1 supplies
I/O power supply.

Block that an Additional I/O
Power Supply Unit 2 supplies
I/O power supply.

NX Unit power supply

Internal

power

supply

circuit

Power
supply

○

Protective
device

• When Total Current Consumption for All Blocks Does Not Exceed the Rated Current

In this example, the current consumption from each power supply is as follows:

Current consumption from Unit power supply: I I_unit2 ≤ Lowest rated current
Current consumption from I/O power supply for NX Units: I_io1 + I_io2 ≤ 4 A (rated current for
I/O power supply)

4 Designing the Power Supply System

4-27

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

4-4 Selecting External Power Supplies and Protective Devices

4-4-3

Selecting Protective Devices

Содержание NX1P2 series









































































































































































































































































Результаты поиска

Содержание NX1P2 series

Отзывы:

Бренды по названию

Популярные бренды

Omron NX1P2 series, Руководство пользователя по оборудованию

Результаты поиска

Содержание NX1P2 series

Отзывы:

Бренды по названию

Популярные бренды