Omron NX1P2 series Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 264

background image

Electrical and Mechanical Specifications

The electrical and mechanical specifications are given below.

Item

Specification

Model

NX1P2-

££

40DT

£

NX1P2-9

£

24DT

£

Enclosure

Mounted in a panel

Dimensions (mm)

154 × 100 × 71 mm (W×H×D)

130 × 100 × 71 mm (W×H×D)

Weight

NX1P2-

££

40DT: 650 g

NX1P2-

££

40DT1: 660 g

NX1P2-9

£

24DT: 590 g

NX1P2-9

£

24DT1: 590 g

Unit power sup-
ply

Power supply
voltage

24 VDC (20.4 to 28.8 VDC)

Unit power con-

NX1P2-

££

40DT: 7.05 W

NX1P2-

££

40DT1: 6.85 W

NX1P2-9

£

24DT: 6.70 W

NX1P2-9

£

24DT1: 6.40 W

Inrush current

For cold start at room temperature:
10 A max./0.1 ms max.
and
2.5 A max./150 ms max.

Current capacity
of power supply

terminal

4 A max.

Isolation method

No isolation: between the Unit power supply terminal and internal cir-
cuit

Power supply to
the NX Unit pow-
er supply

NX Unit power
supply capacity

10 W max.

NX Unit power
supply efficiency

80%

Isolation method

No isolation: between the Unit power supply terminal and NX Unit
power supply

I/O power supply to NX Units

Not provided

External connec-
tion terminals

Communications
connector

RJ45 for EtherNet/IP Communications × 1
RJ45 for EtherCAT Communications × 1

Screwless clamp-
ing terminal block

For Unit power supply input, grounding, and input signal: 1 (Remova-
ble)
For output signal: 1 (Removable)

Output terminal
(service supply)

Not provided

RUN output termi-
nal

Not provided

NX bus connector

8 NX Units can be connected

Option board slot

2

1

*1.

Includes the End Cover, and does not include projecting parts.

*2.

Includes the End Cover. The weight of the End Cover is 82 g.

*3.

Includes the SD Memory Card and Option Board. The NX Unit power consumption to NX Units is not includ-
ed.

*4.

The inrush current may vary depending on the operating condition and other conditions. Therefore, select
fuses, breakers, and external power supply devices that have enough margin in characteristic and capacity,
considering the condition under which the devices are used.

*5.

The amount of current that can be passed constantly through the terminal. Do no exceed this current value
when you use a through-wiring for the Unit power supply.

3 Configuration Units

3-3

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

3-1 CPU Units

3

3-1-1

Models and Specifications

«
...
83
84
85
86
87
...
»

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX1P2 series

Бренд: ZETR Страницы: 2

LS42 - BladeCenter - 7902

Бренд: IBM Страницы: 56

Бренд: IBM Страницы: 2

BladeCenter Management Module

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 110

Remote Supervisor Adapter II

Бренд: IBM Страницы: 132

Бренд: NEC Страницы: 6

MegaRAID SATA 300-4XLP

Бренд: LSI Страницы: 3

Бренд: u-blox Страницы: 29

PowerBeam PBE-5AC-400-ISO

Бренд: Ubiquiti Страницы: 23

Бренд: ACTi Страницы: 14

Wisenet XRN-6410RB2-24TB

Бренд: Hanwha Techwin Страницы: 124

Бренд: ICS ELECTRONICS Страницы: 4

Бренд: AMD Страницы: 27

Бренд: EXAGATE Страницы: 7

Бренд: Cypress Semiconductor Страницы: 32

Бренд: VALKYRIE Страницы: 26

Бренд: InfoStor Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды