manualshive.com logo in svg

Omron NX1P2 series, Руководство пользователя по оборудованию

Поделиться
Скачать
Omron NX1P2 series Скачать руководство пользователя страница 231

Controller

DC I/O
device

AC I/O
device

Terminal block

Example of Arrangement in Panel

Wire Layout for the Power Supply System

Observe the following points when wiring the power supply system.
• Separate the Controller power supply from the I/O device power supply and install a noise filter near

the Controller power supply feed section.

• Use an isolating transformer to significantly reduce noise between the Controller and the ground. In-

stall the isolating transformer between the Controller power supply and the noise filter, and do not
ground the secondary coil of the transformer.

• Keep the wiring between the transformer and the Controller as short as possible, twist the wires

well, and keep the wiring separate from high-voltage and power lines.

Unit power supply for Controller

I/O power supply for Controller

Power Supply System Diagram

Power circuits

Power supply for general operations circuits

 Outlet (for peripheral devices)

I/O power supply for Controller

Noise
filter

Wiring External I/O Signal Lines

Observe the following points when wiring external I/O signal lines.
• To absorb reverse electromotive force when an inductive load is connected to an output signal, con-

nect a surge suppressor near the inductive load in an AC circuit, or connect a diode near the induc-
tive load in a DC circuit.

5 Installation and Wiring

5-87

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

5-5 Control Panel Installation

5

5-5-5

 Electrical Environment

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды