Omron NX1P2 series Скачать руководство пользователя страница 182

Страница: 182 / 264

5-3-12

Removing NX Units

Precautions for Safe Use

Always turn OFF the Unit power supply and I/O power supply before you remove the NX Unit.

Use a flat-blade screwdriver to pull up the DIN Track mounting hook on the Unit to remove.

Flat-blade screwdriver

DIN Track mounting hook

Put your fingers on the protrusions for removing multiple NX Units including the Unit to be re-
moved, then pull out straight forward to remove.

Protrusion for removing the Unit

Precautions for Correct Use

• When removing an NX Unit, remove multiple Units together which include the one you

want to remove. If you attempt to remove only one Unit, it is stuck and hard to pull out.

• Do not unlock the DIN Track mounting hooks on all of the NX Units at the same time.

If you unlock the DIN Track mounting hooks on all of the NX Units at the same time,
all of the Units may come off.

• When you remove a Unit, be careful not to touch or bump the pins in the NX bus con-

nector.

5 Installation and Wiring

5-38

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

Содержание NX1P2 series









































































































































































































































































Результаты поиска

Содержание NX1P2 series

Отзывы:

Бренды по названию

Популярные бренды

Omron NX1P2 series, Руководство пользователя по оборудованию

Результаты поиска

Содержание NX1P2 series

Отзывы:

Бренды по названию

Популярные бренды