Omron NX1P2 series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 264

background image

Terminal

block

Terminal

block

NG

NG

• The angle at which you insert a screwdriver in the release holes on the screwless clamping terminal

blocks of the CPU Unit is different from that on the screwless clamping terminal blocks of NX Units.
Check the wiring method for the NX Unit and perform wiring correctly. Refer to the user’s manual of
the specific NX Unit for how to wire an NX Unit.

Power Supply Design

• Select an external power supply with sufficient capacity by considering the power supply capacity or

inrush current when the power is turned ON that is specified in this manual.
Otherwise, the external power supply may not be turned ON or malfunction due to unstable power
supply voltage.

• Use the I/O power supply current for the CPU Rack of NX1P2 CPU Unit at 4 A or less. Using the

currents that are outside of the specifications may cause failure or damage.

• Use all Units within the I/O power supply ranges that are given in the specifications.
• Do not apply voltages that exceed the rated value to any Input Unit, slave, or input built in the CPU

Unit.

• Do not apply voltages or connect loads to the Output Units, slaves, or CPU Unit’s internal outputs in

excess of the ratings.

• Surge current occurs when the power supply is turned ON. When selecting fuses or breakers for

external circuits, consider the above precaution and allow sufficient margin in shut-off performance.
Refer to this manual for surge current specifications.

• If the full dielectric strength voltage is applied or turned OFF using the switch on the tester, the gen-

erated impulse voltage may damage the Power Supply Unit. Use the adjustment on the tester to
gradually increase and decrease the voltage.

• Install external breakers and take other safety measures against short-circuiting and overcurrents in

external wiring.

• Do not apply voltages or connect loads in excess of the maximum switching capacity.

Turning ON the Power Supply

• It takes approximately 20 seconds to enter RUN mode after the power supply is turned ON. During

that time, digital outputs on the CPU Rack will be OFF. The slave outputs behave according to the
setting values.
Use the system-defined variables and the NX Unit device variables in the user program to confirm
that I/O data communications are established before attempting control operations. External com-
munications are also not performed during startup.

• Configure the external circuits so that the power supply to the control system turns ON only after the

power supply to the Controller has turned ON. If the power supply to the Controller is turned ON
after the control power supply, temporary errors may result in incorrect control system signals

Precautions for Safe Use

22

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

«
...
22
23
24
25
26
...
»

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX1P2 series

Бренд: CSS Страницы: 2

Бренд: Allnet Страницы: 12

Бренд: Telebyte Страницы: 19

Бренд: Telit Wireless Solutions Страницы: 113

ST62GP-EMU2 HDS2 Series

Бренд: STMicroelectronics Страницы: 58

Бренд: Hama Страницы: 6

Бренд: AC Infinity Страницы: 24

BPN-SAS3-116A-N10

Бренд: Supermicro Страницы: 8

Бренд: Abus Страницы: 98

Бренд: IceManCooler Страницы: 2

Бренд: Behringer Страницы: 15

Бренд: SeaLevel Страницы: 19

Бренд: Devolo Страницы: 24

Schoeps electret

Бренд: VAMISOUND Страницы: 15

Бренд: Cambium Networks Страницы: 208

HDMI Input Card DMC-HD

Бренд: Crestron Страницы: 1

Бренд: Sonnet Страницы: 8

Бренд: CAMBRIONIX Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды