manualshive.com logo in svg

Omron NX1P2 series, Руководство пользователя по оборудованию

Поделиться
Скачать
Omron NX1P2 series Скачать руководство пользователя страница 124

- When different I/O power supply voltage are used.
- When separating the power supply systems.

NX Unit

NX Unit

NX Unit

End
Cover

Separated by the 
Additional I/O Power 
Supply Unit

NX-series NX1P2
CPU Unit

Unit power supply terminals

Internal 

power 

supply

circuit

Internal 

circuits

NX Unit power supply

Unit power 

supply

(24 VDC)

I/O power supply 

terminals

Additional 
I/O Power 
Supply 
Unit

Additional 
I/O Power 
Supply 
Unit

I/O power supply

(12 VDC, etc.)

I/O power supply

(24 VDC, etc.)

○

○

○

○

○

○

I/O power supply

I/O power supply

NX bus connector

I/O power supply terminals

I/O power supply voltage

24 VDC

I/O power supply voltage

12 VDC

I/O Power Supply Connection Unit

You can add an I/O Power Supply Connection Unit to provide additional I/O power supply terminals if
required to connect external devices to a Digital I/O Unit or Analog I/O Unit.
The following figure shows how to use I/O Power Supply Connection Units. Assume that a PNP-type
Digital Input Unit, NX-ID5342, is used to input signals from a two-wire sensor and a three-wire sensor
with NPN output. The NX-ID5342 Digital Input Unit does not have I/O power terminals. For the Digital
Input Unit, you need to prepare IOG terminals for the two-wire sensor, and IOV terminals as well as
IOG terminals for the three-wire sensor. Insert two I/O Power Supply Connection Units: one is NX-
PC0020 with 16 IOV terminals, and the other is NX-PC0010 with 16 IOG terminals. Wire them as
shown in the figure below.
The NX Unit power supply line as well as the I/O power supply line is connected between the I/O Pow-
er Supply Connection Units and adjacent NX Units through the NX bus.

4 Designing the Power Supply System

4-8

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды