manualshive.com logo in svg

Omron NX1P2 series, Руководство пользователя по оборудованию

Поделиться
Скачать
Omron NX1P2 series Скачать руководство пользователя страница 200

l

Connecting Ferrules

Insert the ferrule straight into the terminal hole.
It is not necessary to press a flat-blade screwdriver into the release hole.

Ferrule

After you make a connection, make sure that the ferrule is securely connected to the terminal
block.

l

Connecting Twisted Wires/Solid Wires

Use the following procedure to connect the twisted wires or solid wires to the terminal block.

1

Press the a flat-blade screwdriver straight into the release hole.
If you press in the screwdriver correctly, you will feel the spring in the release hole, and the
screw driver will begin to incline.

Release hole

Flat-blade screwdriver

1

2

Leave the flat-blade screwdriver pressed into the release hole and insert the twisted wire or the
solid wire into the terminal hole.
Insert the twisted wire or the solid wire until the stripped portion is no longer visible to prevent
shorting.

2

Twisted wire/Solid wire

3

Remove the flat-blade screwdriver from the release hole.

5 Installation and Wiring

5-56

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды