Omron NX1P2 series Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 264

background image

Support Software

You can use the following Support Software to set up, monitor, and debug an NX-series Controller.
• Sysmac Studio

The Sysmac Studio is the main Support Software that you use for an NX-series Controller. On it,
you can set up the Controller configurations, parameters, and programs, and you can debug and
simulate operation.

• Other Support Software

The following Support Software is also included in the Sysmac Studio Software Package Standard
Edition.

Configuration software

Application

Sysmac Studio

The Sysmac Studio is used for sequence control, motion control, and all other operations
except those described below.

Network Configurator

The Network Configurator is used for tag data links on EtherNet/IP ports.

CX-Integrator

The CX-Integrator is used for remote I/O communications with a CJ-series DeviceNet Unit
or CJ-series CompoNet Master Unit.

CX-Protocol

The CX-Protocol is used for protocol macros with the CJ-series Serial Communications
Units.

CX-Designer

The CX-Designer is used to create screens for NS-series PTs.

*1.

If the NJ/NX-series Controller is a target device, you may also use Sysmac Studio version 1.10 or higher. Use the Network
Configurator if a CS/CJ-series PLC operates as the originator device.

1 Introduction to NX-series Controllers

1-8

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

«
...
58
59
60
61
62
...
»

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX1P2 series

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

Бренд: Tripp Lite Страницы: 20

Parallel Printer Card PIOC

Бренд: B&B Electronics Страницы: 16

Бренд: axing Страницы: 52

Бренд: Compro Technology Страницы: 2

Бренд: OPTO 22 Страницы: 28

Бренд: PairGain Страницы: 80

Бренд: CopperOptics Страницы: 12

Бренд: HMS Страницы: 18

Бренд: EMC Страницы: 88

Kontron CP3005 Series

Бренд: S&T Страницы: 115

Braswell Series

Бренд: Intel Страницы: 54

6026 Lapbank 16 mini

Бренд: Loxit Страницы: 2

Бренд: TEC Control Страницы: 4

Бренд: JCAT Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды