manualshive.com logo in svg

Omron NX1P2 series, Руководство пользователя по оборудованию

Поделиться
Скачать
Omron NX1P2 series Скачать руководство пользователя страница 66

1-3

Overall Operating Procedure for the

CPU Unit

This section gives the overall operating procedure for the NX1P2 CPU Unit and then describes it in
more detail.

1-3-1

Overall Procedure

The overall procedure to use an NX1P2 CPU Unit is given below.

STEP 1. Software Design

Design the overall system configuration, task configuration, programs, and variables.
Step 1-1 Designing I/O and Processing
Step 1-2 Designing Tasks
Step 1-3 Designing Programs

STEP 2. Software Setups and Programming

Create the system configurations that you designed in step 1 on the Support Software and assign
the variables. Create the tasks and programs, and debug them, e.g., with simulations.
Step 2-1 Slave and NX Unit Configurations
Step 2-2 Controller Setup
Step 2-3 Programming
Step 2-4 Offline Debugging

STEP 3. Mounting and Setting Hardware

Mount the Units and make the required hardware settings.

STEP 4. Wiring

Connect the network cables and wire the I/O.

STEP 5. Confirming Operation and Starting Actual System Opera-

tion

Connect the Support Software to the physical system and download the project. Check operation
on the physical system and then start actual system operation.

1 Introduction to NX-series Controllers

1-14

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды