Omron NX1P2 series Скачать руководство пользователя страница 140 | Manualshive

Страница: 140 / 264

background image

= (CPU Unit power consu Total power consumption from NX Unit power supply of NX
Units connected to CPU Unit)/NX Unit power supply efficiency of CPU Unit
= 7.05 W + (0.85 W × 1 + 0.90 W × 4 + 1.20 W × 3)/0.8
= Approx. 17.1 W

The above is the constant power consumption during operation. When you select the power supply,
consider the inrush current that will flow when the power is turned ON.
Refer to

Electrical and Mechanical Specifications

on page 3-3 under

3-1-1 Models and Specifica-

on page 3-2 for information on inrush current specifications.

Precautions for Safe Use

Select an external power supply with sufficient capacity by considering the power supply ca-
pacity or inrush current when the power is turned ON. Otherwise, the external power supply
may not be turned ON or it may malfunction due to unstable voltage.

4-4-2

Selecting the I/O Power Supplies

This section describes how to select the I/O power supplies for the CPU Rack.

Recommended Power Supplies

Use an SELV power supply that meets the following conditions for the I/O power supply.
• Has overcurrent protection.
• Has double or reinforced insulation between the input and output.
• Has an output voltage of 5 to 24 VDC (4.5 to 28.8 VDC).*1

*1. Use an output voltage that is appropriate for the I/O circuits of the NX Units and the connected external devi-

ces.

Recommended Power Supplies: S8VK-S Series (manufactured by OMRON)

Calculating the Required Power Supply Capacity of the I/O Power

Supply for NX Units

Use the calculation method that is described in

4-3-2 Designing the I/O Power Supply from the NX

on page 4-14 and calculate the total current consumption from the I/O power supply and the re-

quired power supply capacity of the I/O power supply.
Unlike the Unit power supply, it is not necessary to use only one I/O power supply to supply power to
all NX Units on the CPU Rack.

Precautions for Safe Use

Select an external power supply with sufficient capacity by considering the power supply ca-
pacity or inrush current when the power is turned ON. Otherwise, the external power supply
may not be turned ON or it may malfunction due to unstable voltage.

4 Designing the Power Supply System

4-24

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

«
...
138
139
140
141
142
...
»

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX1P2 series

Бренд: Laird Страницы: 36

Бренд: CSS Страницы: 2

Power Control Processor

Бренд: ETC Страницы: 64

Core 2 Quad Q9400

Бренд: Intel Страницы: 2

ELITENAS EN104L+(B)

Бренд: Sans Digital Страницы: 9

Бренд: PairGain Страницы: 80

Бренд: CyberResearch Страницы: 59

Бренд: Multi-Link Страницы: 31

Бренд: MicroNova Страницы: 113

Бренд: SilverStone Страницы: 16

Бренд: Roland Страницы: 224

Бренд: Commax Страницы: 122

Бренд: Promax Страницы: 32

Бренд: Reach Страницы: 21

Бренд: IBT Страницы: 26

Бренд: IBM Страницы: 34

Бренд: IBM Страницы: 28

Бренд: IBM Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды