Omron NX1P2 series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 264

background image

Restricted region

(shaded portion)

• The End Cover has a metal portion and is heavier than it looks. Be careful not to drop it when han-

dling.

Installation

• Always connect to a ground of 100 Ω or less when installing the Units.

Wiring

• Follow the instructions in this manual to correctly perform wiring.

Double-check all wiring and switch settings before turning ON the power supply.

• Use the methods that are specified in this manual for wiring the terminal blocks.
• Use crimp terminals for wiring the M3 screw terminal blocks. Do not connect bare stranded wires

directly to the M3 screw terminal blocks.

• Use the correct wiring parts and tools when you wire the system. Otherwise, cables may be discon-

nected to cause short-circuit or wire breakage.

• Do not pull on the cables or bend the cables beyond their natural limit.

Do not place heavy objects on top of the cables or other wiring lines. Doing so may break the ca-
bles.

• Mount terminal blocks, connectors, and Option Boards only after checking the mounting location

carefully.

• Be sure that the terminal blocks, communications cables, and Option Boards with tightening screws

or locking devices are properly tightened to or locked into place.

• If the external power supply to a built-in output, Output Unit or slave has polarity, connect it with the

correct polarity. If the polarity is reversed, current may flow in the reverse direction and damage the
connected devices regardless of the operation of the Controller.

• When you insert a flat-blade screwdriver into a release hole on a screwless clamping terminal block

of CPU Unit, press it down with a force of 30N or less. Applying excessive force may damage the
terminal block.

• Do not incline or twist the flat-blade screwdriver while it is in a release hole on a screwless clamping

terminal block of CPU Unit. Doing so may damage the terminal block.

Precautions for Safe Use

21

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

«
...
21
22
23
24
25
...
»

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX1P2 series

Бренд: Barracuda Networks Страницы: 2

Бренд: GE Страницы: 93

Бренд: NEC Страницы: 6

Бренд: IBM Страницы: 63

LoadMaster 1500

Бренд: KEMP Technologies Страницы: 71

Бренд: ZALMAN Страницы: 8

Бренд: Xyclop Страницы: 144

Бренд: Silvertel Страницы: 9

UST510-52B-FL Series

Бренд: AXIOMTEK Страницы: 77

LL140 RGB Series

Бренд: Corsair Страницы: 30

Бренд: ExtraHop Страницы: 3

Бренд: ZALMAN Страницы: 9

Бренд: Tachosys Страницы: 15

Firebox T85-PoE

Бренд: Watchguard Страницы: 27

SECURE BOOT STICK FX

Бренд: Ecos Страницы: 22

Бренд: Fujitsu Страницы: 14

Бренд: Axis Страницы: 10

Бренд: Magnescale Страницы: 73

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды