Omron NX1P2 series Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 264

background image

Letter

Name

Function

E

Input terminal block

This terminal block is used for wiring for the Unit power sup-
ply, grounding, and built-in input.

F

Input indicator

Shows the operation status of the built-in input.

Built-in I/O Operation Status Indicators

G

Unit hookup guides

These guides are used to mount an NX Unit or End Cover.

H

NX bus connector

This connector is used to connect the CPU Unit to the NX
Unit on the right of the CPU Unit.

I

Option board slot 1 (left)
Option board slot 2 (right)

Remove the covers of the slots and mount Option Boards.
For the models with 24 built-in I/O points, only one slot is pro-
vided. Keep the removed covers in a safe place.

J

Output indicator

Shows the operation status of the built-in output.

Built-in I/O Operation Status Indicators

K

Output terminal block

This terminal block is used to wire the built-in output.

L

CPU Unit operation status indicator

Shows the operation status of the CPU Unit.

3-1-3 Operation Status Indicators

M

Battery connector

Connector to mount the backup battery that is sold separate-
ly.

N

Battery slot

Used to mount the backup battery that is sold separately.

O

Built-in EtherCAT port (port 2)

Connects the built-in EtherCAT with an Ethernet cable.

P

Built-in EtherNet/IP port (port 1)

Connects the built-in EtherNet/IP with an Ethernet cable.

Q

SD Memory Card cover

Cover for the SD Memory Card and DIP switch. The cover
swings upward.

R

End Cover

Cover to protect the CPU Unit and NX Units.
One End Cover is provided with the CPU Unit.

S

Battery cover

Cover for the battery slot. Remove this cover when you
mount/remove the battery.

T

ID information indication

Shows the ID information of the CPU Unit.

3-1-6 ID Information Indication

U

DIN Track contact plate

This plate is connected internally to the functional ground ter-
minal on the terminal block.

*1.

To use Safe Mode, set the DIP switch as shown below and then turn ON the power supply to the Controller.

OFF

ON

O
N

1

2

3

4

If the power supply to the Controller is turned ON with the CPU Unit in Safe Mode, the CPU Unit will start in
PROGRAM mode. Use the Safe Mode if you do not want to execute the user program when the power sup-
ply is turned ON or if it is difficult to connect the Sysmac Studio.
For information on Safe Mode, refer to the

NJ-series Troubleshooting Manual (Cat. No. W503)

.

*2.

Refer to the

NJ-series CPU Unit Software User’s Manual (Cat. No. W501)

for details on backing up data.

3 Configuration Units

3-6

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

«
...
86
87
88
89
90
...
»

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX1P2 series

Бренд: Alesis Страницы: 46

Urban Wireless CC-VT240W

Бренд: Cateye Страницы: 15

Бренд: IOtech Страницы: 16

Бренд: Telex Communications Страницы: 28

Бренд: Paradyne Страницы: 10

Бренд: Tandy Страницы: 24

Vocal Performer VE-20

Бренд: Boss Страницы: 20

Бренд: S&T Страницы: 28

Powereta iQP Series

Бренд: TDK Страницы: 2

KÜHLER H2O 920

Бренд: Antec Страницы: 6

IA611 Xplained Pro

Бренд: Knowles Страницы: 14

Бренд: Dave Embedded Systems Страницы: 79

Бренд: Magewell Страницы: 10

Бренд: Z3 Technology Страницы: 18

Бренд: Keithley Страницы: 108

Бренд: Xinje Страницы: 76

Бренд: Juniper Страницы: 6

Бренд: Qlogic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды