Omron NX1P2 series Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 264

background image

Indicator

Color

Status

Meaning

RUN

Green

Lit.

The CPU Unit is in normal operation in RUN mode. (The user program
is in execution.)

Flashing

at 2-s intervals,
then flashing at

0.5-s intervals.

The CPU Unit is starting (entering RUN mode or PROGRAM mode at
startup).

Flashing

at 2-s intervals

continues for

30 seconds or

longer.

System initialization error occurs.

Not lit.

Operation is stopped in PROGRAM mode, when a CPU Unit reset is in
progress, or when any of the following errors occurs.

•

Controller error in the major fault level

•

CPU error (WDT error)

ERROR

Red

Lit.

Self-diagnosis found one of the following errors.

•

Controller error in the major fault level

•

CPU error

Flashing

at 1-s intervals.

Self-diagnosis found one of the following errors.

•

Controller error in the partial fault level (an error in which all control
of a Function Module is disabled)

•

Controller error in the minor fault level (an error in which partial con-
trol of a Function Module is disabled)

CPU Unit operation will continue for either of these errors.
Operation will stop for the Function Module in which a Controller error
in the partial fault level occurred.
Operation will continue for the Function Module in which a Controller
error in the minor fault level occurred.

Not lit.

The CPU Unit is in normal operation, a CPU reset is in progress, or
monitored information occurred (CPU Unit operation will continue.).

BUSY

Yellow

Flashing

Built-in non-volatile memory access in progress.

Not lit.

Other than the above.

SD PWR

Green

Lit.

Power is being supplied to the SD Memory Card and the SD Memory
Card can be used.

Flashing

A backup, restore or verification operation is in progress.

Not lit.

The power supply for the SD Memory Card is stopped, an SD Memory
Card is not mounted, or the file format of the mounted SD Memory
Card is not supported.

SD BUSY

Yellow

Flashing

SD Memory Card access in progress.

Not lit.

SD Memory Card access not in progress.

*1.

Refer to the

NJ/NX-series CPU Unit Software User’s Manual (Cat. No. W501)

for details on backing up data.

3 Configuration Units

3-8

NX-series NX1P2 CPU Unit Hardware User’s Manual (W578)

«
...
88
89
90
91
92
...
»

Содержание NX1P2 series









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NX1P2 series

WS-650 lite Series

Бренд: Laurell Страницы: 84

Бренд: Javad Страницы: 35

Бренд: Phytec Страницы: 53

Бренд: ZyXEL Communications Страницы: 2

Бренд: Dahua Страницы: 24

Бренд: Nvidia Страницы: 115

IPAM-1600s Series

Бренд: C-Com Страницы: 148

Бренд: Advantech Страницы: 36

Бренд: TRENDnet Страницы: 12

Bluespoon 17-1000

Бренд: Radio Shack Страницы: 1

Бренд: INNOSILICON Страницы: 11

Бренд: NZXT Страницы: 2

Бренд: Alcatel-Lucent Страницы: 60

Tamar FCSAS102800

Бренд: Bridgeworks Страницы: 56

Бренд: RR-Concepts Страницы: 12

Бренд: Omron Страницы: 14

NVR2104/2108HS-W-4KS2 1U

Бренд: Dahua Technology Страницы: 363

Бренд: Renesas Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды