Omron NT-SERIES - SUPPORT TOOL FOR WINDOWS V4 Скачать руководство пользователя страница 314 | Manualshive

Страница: 314 / 594

background image

7-7

Section

I/O Comment Table

298

7-6-1 Operation Procedure

An extended I/O output table entry is displayed by following the operation de-
scribed below.

Select [Tools] (menu bar)

→

[Table]

→

[Extended I/O Output] tab

Setting

With an extended I/O output table entry, the objective of an operation is specified
by clicking on the line. Setting is performed by using the setting dialog box that is
displayed by clicking on

.

For the operation procedure for

,

, and

,

refer to

7-1 Common Operation

.

7-6-2 Description of Extended I/O Output Table Fields

No.

Extended I/O unit output terminal number.

PLC Address

Specify the PC (PLC) bit that controls the output terminal of an extended I/O unit.

I/O Comment

Specify a comment for a PC (PLC) bit.
A comment can comprise up to 16 characters.

7-7

I/O Comment Table

The I/O comment table is an area provided in a PT to manage the comment data
of all words and bits in a PC (PLC) that are set by the Support Tool.

It displays comments on PC (PLC) words and bits specified by numeral memory
table entries, character string memory table entries (string table), bit memory

«
...
312
313
314
315
316
...
»

Содержание NT-SERIES - SUPPORT TOOL FOR WINDOWS V4



















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NT-SERIES - SUPPORT TOOL FOR WINDOWS V4

SmartOffice SmartOffice Mobile

Бренд: Palm Страницы: 29

Venture IP Telephone System

Бренд: Aastra Страницы: 12

ANTI-VIRUS 2011 - REV 2011.03

Бренд: AVG Страницы: 211

CERTIFICATE SYSTEM 8 - AGENTS GUIDE

Бренд: Red Hat Страницы: 146

Active Management Technology v5.0

Бренд: Intel Страницы: 143

Бренд: Intel Страницы: 212

MAPCREATE 7 - ADDENDUM

Бренд: LEI Extras Страницы: 16

Бренд: beat buddy Страницы: 33

05720-017408-9621 - AE AUTOCAD LT 2000I LAB-PK 10U CD

Бренд: Autodesk Страницы: 21

00128-051462-9340 - AutoCAD 2008 - PC

Бренд: Autodesk Страницы: 48

Бренд: Focusrite Страницы: 9

Loopfactory AN200

Бренд: Yamaha Страницы: 72

QConvergeConsole CLI 2400 Series

Бренд: Qlogic Страницы: 366

PERFORMANCE MANAGEMENT FOR POWER SYSTEMS - INTERACTIVE GRAPHING SUPPORT FOR ...

Бренд: IBM Страницы: 29

ANTI-EXECUTABLE - PRODUCT

Бренд: FARONICS Страницы: 2

DEEP FREEZE ENTERPRISE 6

Бренд: FARONICS Страницы: 64

Бренд: Datavideo Страницы: 141

INTUITY Messaging Solutions

Бренд: Lucent Technologies Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды