Omron NT-SERIES - SUPPORT TOOL FOR WINDOWS V4 Скачать руководство пользователя страница 527 | Manualshive

Страница: 527 / 594

Omron NT-SERIES - SUPPORT TOOL FOR WINDOWS V4 Скачать руководство пользователя страница 527

Appendix D

Translation Support Utility

511

(5) When closing the source MMI file or exiting the Translation Support Utility, if

you have made some translation changes that have not been committed to
MMI files corresponding to target languages, the Translation Support Utility
will prompt you to generate the corresponding MMI for the target languages
(if any). Refer to the message below.

(6) If the current source MMI file is newer than the one registered in the MDB

database or it has contents that are different from the MDB database file,
then it prompts you whether to update the database with the information of
the current file or not. Refer to the message below.

(7) File save error when saving translated target MMI files. Refer to the follow-

ing image for a sample.

System Function

Translation Scope and Policy

(1) Only the following kinds of label translation are supported, subject to avail-

ability in the target PT model of the source application:

«
...
525
526
527
528
529
...
»

Содержание NT-SERIES - SUPPORT TOOL FOR WINDOWS V4



















































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды