NSK EDD Megatorque Motor страница 205 Скачать руководство пользователя | Manualshive

Страница: 205 / 398

background image

8. More Advanced Function

— 8-21 —

8.3.3. Travel Limit Output (±): OTXA



Reports that the Motor gets in the area specified by the travel limits.
(For both cases of software and hardware over travel limits.)



Different from the outputs OTPA and OTMA, there is no function to distinguish the direction of limit
switch.

Table 8-22: Signal logic of the output OTXA

Logic

Description

Open

Normal

Closed

Limit activated



When the travel limit activates, the following alarms will occur.

Table 8-23: Indication of 7 segments LED at activation of over travel limit

7segmetns LED

Command TA (Tell alarm)

Description

F2

F2>Software Over Travel

Software over travel

F3

F3>Hardware Over Travel

Hard ware over travel

Fig 8-10: Motion timing with the input OTP and the output OTXA (In case of positive logic)

The Motor stops immediately with the Motor

servo on.

Motor motion

closed

open

OFF

closed

opem

Ouput DRDY

Input OTP

Outpu SVST

closed

open

closed

open

Output BUSY

closed

open

closed

open

Output IPOS
(FW

> 0: FIN

)

Output OTXA

ON

OFF

Max. 1 ms

Max. 1 ms

Max. 1 m

s

Output IPOS
(FW <

0: CFIN)

(FW

＝

0:IPOS

)

Put the Motor in servo-off state by
the input SVON.

Move the Motor out of the area, or turn off the

Motor servo and move the Motor manually



When a travel limit is detected in the middle of operation, the Motor stops before it reaches the target
position. Thus, the output IPOS (In-position) does not close.



When the travel limit is detected while the Motor is stopping, the output IPOS does not change because
the System maintains the position at where the last positioning was completed.

«
...
203
204
205
206
207
...
»

Содержание EDD Megatorque Motor















































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDD Megatorque Motor

SO ROAD MOVIE CAR PACK

Бренд: DANE-ELEC Страницы: 14

Бренд: DANE-ELEC Страницы: 2

Бренд: DANE-ELEC Страницы: 16

Бренд: DANE-ELEC Страницы: 16

Бренд: DANE-ELEC Страницы: 2

SO XSTREAM FULL HD -

Бренд: DANE-ELEC Страницы: 2

Бренд: Omega Digitech Страницы: 8

Бренд: Wacker Neuson Страницы: 254

Бренд: µ-Dimension Страницы: 6

Бренд: GADGETMONSTER Страницы: 26

Бренд: Wyrestorm Страницы: 4

Бренд: Engel Страницы: 42

Бренд: Samlex Europe Страницы: 33

Бренд: Jaden Страницы: 173

Бренд: Perle Страницы: 23

DMX SPLITTER 8R

Бренд: GLG Страницы: 2

Бренд: DAB Страницы: 18

Бренд: Fronius Страницы: 135

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды