NetApp StorageGRID SG5712 Скачать руководство пользователя

Страница: 2 / 89

Contents

StorageGRID appliance overview.................................................................................. 4

Controllers in the StorageGRID appliance..................................................................................................................... 6

Installation and deployment overview........................................................................... 8

Preparing for installation.............................................................................................. 10

Port bond modes for E5700SG controller ports............................................................................................... 15

Gathering installation information................................................................................................................................16

Installing the hardware................................................................................................. 21

Status indicators on the E5700SG controller....................................................................................................27

Configuring the hardware.............................................................................................30

Configuring StorageGRID connections........................................................................................................................30

Accessing and configuring SANtricity System Manager............................................................................................. 47

Optional: Changing the RAID mode (SG5760 only)................................................................................................... 53
Optional: Remapping network ports for the appliance.................................................................................................54

Deploying an appliance Storage Node......................................................................... 55

Troubleshooting the hardware installation..................................................................58

Hardware setup appears to hang................................................................................................................................... 58

Hardware Installation and Maintenance Guide for SG5700 Appliances

Contents

Содержание StorageGRID SG5712


























































































Результаты поиска

Содержание StorageGRID SG5712

Отзывы:

Похожие инструкции для StorageGRID SG5712

Бренды по названию

Популярные бренды

NetApp StorageGRID SG5712, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание StorageGRID SG5712

Отзывы:

Похожие инструкции для StorageGRID SG5712

Бренды по названию

Популярные бренды