NetApp StorageGRID SG5712 Скачать руководство пользователя | Manualshive

Страница: 48 / 89

background image

Setting the IP address for the E2800 management port

Management port 1 on the E2800 controller connects the appliance to the management network
for SANtricity System Manager. You must set a static IP address for the E2800 controller to
ensure that you do not lose your management connection to the hardware and the controller
firmware in the StorageGRID appliance.

About this task

DHCP-assigned addresses could change at any time. Assign a static IP address to the controller to
ensure consistent accessibility.

Steps

1. From the client, enter the URL for the StorageGRID Appliance Installer:

https://E5700SG_Controller_IP:8443

For

E5700SG_Controller_IP

, use the IP address for the appliance on any StorageGRID

network.

The StorageGRID Appliance Installer Home page appears.

2. Select Hardware Configuration > Storage Controller Network Configuration.

The Storage Controller Network Configuration page appears.

3. Depending on your network configuration, select Enabled for IPv4, IPv6, or both.

4. Make a note of the IPv4 address that is automatically displayed.

DHCP is the default method for assigning an IP address to this port.

Note: It might take a few minutes for the DHCP values to appear.

5. Optionally, set a static IP address for the E2800 controller management port.

Note: You should either assign a static IP for the management port or assign a permanent
lease for the address on the DHCP server.

a. Select Static.

b. Enter the IPv4 address, using CIDR notation.

c. Enter the default gateway.

d. Click Save.

It might take a few minutes for your changes to be applied.

Hardware Installation and Maintenance Guide for SG5700 Appliances

48

Configuring the hardware

«
...
46
47
48
49
50
...
»

Содержание StorageGRID SG5712


























































































Отзывы:

Нет отзывов

Похожие инструкции для StorageGRID SG5712

Бренд: CAME Страницы: 4

Бренд: Vanguard Страницы: 121

Бренд: Salus Страницы: 16

Бренд: Accusys Страницы: 34

Бренд: IEI Technology Страницы: 3

Бренд: Hama Страницы: 12

Бренд: TP-Link Страницы: 2

DesignCore RVP-TDA3 Series

Бренд: D3 Страницы: 34

Бренд: XtendLan Страницы: 228

EK-Loop Modulus Series

Бренд: ekwb Страницы: 7

Бренд: Cervoz Страницы: 22

Quadro M6000 Sync

Бренд: Nvidia Страницы: 8

SiliconDrive SSD-P16G(I)-3100

Бренд: Silicon Systems Страницы: 108

Бренд: MEDIATEK Страницы: 166

OptiBond 210 C Series

Бренд: i-MO Страницы: 16

Бренд: INNOSILICON Страницы: 11

Бренд: NZXT Страницы: 2

Бренд: ZiLOG Страницы: 317

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды