NetApp StorageGRID SG5712 Скачать руководство пользователя | Manualshive

Страница: 62 / 89

background image

About this task

CAUTION: The following steps are only applicable
when you are using the Grid Manager to perform the
upgrade. The storage controllers in the SG5700 series
appliance cannot be upgraded using the Grid Manager
when the controllers are using SANtricity OS older than
08.42.20.00 (11.42).

Note: You cannot perform other software updates (StorageGRID software upgrade or a hotfix)
until you have completed the SANtricity OS upgrade process. If you attempt to start a hotfix or
a StorageGRID software upgrade before the SANtricity OS upgrade process has finished, you
are redirected to the SANtricity OS upgrade page.

Note: The procedure will not be complete until the SANtricity OS upgrade has been
successfully applied to all applicable nodes. It might take more than 30 minutes to load the
SANtricity OS software on each node and up to 90 minutes to reboot each StorageGRID storage
appliance.

Note: This procedure will automatically upgrade the NVSRAM to the most recent version
associated with the SANtricity OS upgrade.

Steps

1.

From a service laptop or management client, download the new SANtricity OS Software file
from the NetApp support site.

Be sure to choose the SANtricity OS version for the E2800 storage controllers.

NetApp Downloads: SANtricity OS

2.

Sign in to the Grid Manager using a supported browser.

3.

Select Maintenance. Then, in the System section of the menu, select Software Update.
The Software Update page appears.

4.

Click SANtricity OS.

The SANtricity OS page appears.

Hardware Installation and Maintenance Guide for SG5700 Appliances

62

Maintaining the SG5700 appliance

«
...
60
61
62
63
64
...
»

Содержание StorageGRID SG5712


























































































Отзывы:

Нет отзывов

Похожие инструкции для StorageGRID SG5712

Kinetic FLT 80 D5/DDC Body

Бренд: EK-Quantum Страницы: 16

Бренд: Allnet Страницы: 12

Бренд: Telebyte Страницы: 19

Бренд: XtendLan Страницы: 228

LinkStation Mini

Бренд: Buffalo Страницы: 71

Бренд: IDT Страницы: 292

DataPlot CB1224

Бренд: B-G Instruments Страницы: 4

ExpressBox2 EB2

Бренд: Magma Страницы: 74

Бренд: Hauppauge Страницы: 55

Бренд: Avenview Страницы: 28

LMP-1202G-SFP Series

Бренд: ANTAIRA Страницы: 19

Бренд: Alarm Страницы: 5

FiberTwist G6426

Бренд: Genexis Страницы: 9

Disc Publisher XR

Бренд: Primera Страницы: 2

Industrial Network Track OSI

Бренд: GarrettCom Страницы: 10

2410SA - Serial ATA RAID Controller

Бренд: Adaptec Страницы: 14

Бренд: Xtreme Страницы: 83

Бренд: ZyXEL Communications Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды