NetApp StorageGRID SG5712 Скачать руководство пользователя | Manualshive

Страница: 20 / 89

background image

Information needed

Your value

VLAN tagging enabled

Choose one:

•

No (default)

•

Yes

VLAN tag

(if VLAN tagging is enabled)

Enter a value between 0 and 4095:

DHCP-assigned IP address for the Client Network, if
available after power on

•

IPv4 address (CIDR):

•

Gateway:

Static IP address you plan to use for the appliance
Storage Node on the Client Network

Note: If the Client Network is enabled, the default
route on the controller will use the gateway specified
here.

•

IPv4 address (CIDR):

•

Gateway:

Related concepts

Port bond modes for E5700SG controller ports

When configuring network links for the E5700SG controller ports, you can use port bonding for
the 10/25-GbE ports that connect to the Grid Network and optional Client Network, and the 1-GbE
management ports that connect to the optional Admin Network. Port bonding helps protect your
data by providing redundant paths between StorageGRID networks and the appliance.

Related tasks

Configuring the hardware

After applying power to the appliance, you must configure SANtricity System Manager, which is
the software you will use to monitor the hardware. You must also configure the network
connections that will be used by StorageGRID.

Related reference

Reviewing appliance network connections

Before installing the StorageGRID appliance, you should understand which networks can be
connected to the appliance and how the ports on each controller are used.

Hardware Installation and Maintenance Guide for SG5700 Appliances

20

Preparing for installation

«
...
18
19
20
21
22
...
»

Содержание StorageGRID SG5712


























































































Отзывы:

Нет отзывов

Похожие инструкции для StorageGRID SG5712

Бренд: EAW Страницы: 10

Бренд: EAW Страницы: 6

Бренд: EAW Страницы: 6

Бренд: Quick Eagle Networks Страницы: 4

Бренд: AMD Страницы: 20

HiGain HLU-231 List 8F

Бренд: ADC Страницы: 7

Бренд: NETGEAR Страницы: 84

Бренд: Dolphin Страницы: 9

Бренд: TP-Link Страницы: 110

Бренд: Jøtul Страницы: 20

Бренд: Nilox Страницы: 66

Бренд: NBase Страницы: 18

Бренд: Gearlinx Страницы: 23

Бренд: MA lighting Страницы: 49

Бренд: Dataprobe Страницы: 16

RoteFinder RF500S

Бренд: Multi-Tech Страницы: 134

N-FXE 02B Series

Бренд: Lantronix Страницы: 10

Бренд: Kontron Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды