NetApp StorageGRID SG5712 Скачать руководство пользователя | Manualshive

Страница: 50 / 89

background image

Related tasks

Setting the IP address for the E2800 management port

Management port 1 on the E2800 controller connects the appliance to the management network
for SANtricity System Manager. You must set a static IP address for the E2800 controller to
ensure that you do not lose your management connection to the hardware and the controller
firmware in the StorageGRID appliance.

Related reference

Web browser requirements

You must use a supported web browser.

Setting up SANtricity System Manager

After accessing SANtricity System Manager, you can use it to configure hardware settings.
Typically, you configure these settings before deploying the appliance as a Storage Node in a
StorageGRID system.

About this task

You use SANtricity System Manager to configure the following settings:

•

Email alerts, SNMP alerts, or syslog alerts for the appliance hardware

•

AutoSupport settings for the appliance hardware

•

Drive Security keys, which are needed to unlock secured drives (this step is required if you are
using FDE or FIPS drives and the Drive Security feature is enabled)

•

Administrator password for accessing SANtricity System Manager

Steps

1. Open a web browser on a management client, and enter the URL for SANtricity System

Manager:

Hardware Installation and Maintenance Guide for SG5700 Appliances

50

Configuring the hardware

«
...
48
49
50
51
52
...
»

Содержание StorageGRID SG5712


























































































Отзывы:

Нет отзывов

Похожие инструкции для StorageGRID SG5712

Бренд: Linksys Страницы: 2

Бренд: Niveo Страницы: 155

Бренд: Aewin Technologies Страницы: 86

Бренд: Hauppauge Страницы: 62

Бренд: QTech Страницы: 406

Бренд: Laser Страницы: 4

NVR2104/2108HS-W-4KS2 1U

Бренд: Dahua Technology Страницы: 363

Бренд: Digi Страницы: 75

Ultra WiFi Booster

Бренд: Optus Страницы: 8

Air Live GW-300R

Бренд: Ovislink Страницы: 20

EZ Switch SMC-EZ1024FDT

Бренд: SMC Networks Страницы: 4

Total Access 1500 Dual FXS/DPO

Бренд: ADTRAN Страницы: 2

ACL-8112 Series

Бренд: NuDAQ Страницы: 92

Бренд: Westermo Страницы: 22

CU8210-D001-0200

Бренд: Beckhoff Страницы: 25

Бренд: Motorola Страницы: 376

Бренд: Motorola Страницы: 20

Бренд: MSE Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды