NetApp StorageGRID SG5712 Скачать руководство пользователя

Страница: 36 / 89

2. If you plan to use the 25-GbE link speed for the 10/25 GbE ports, select 25GbE from the Link

speed drop-down list.

The network switches you are using for the Grid Network and the Client Network must also
support and be configured for this speed. SFP28 transceivers must be installed in the ports.

3. Enable or disable the StorageGRID networks you plan to use.

The Grid Network is required. You cannot disable this network.

a. If the appliance is not connected to the Admin Network, unselect the Enable network

check box for the Admin Network.

b. If the appliance is connected to the Client Network, select the Enable network check box

for the Client Network.

Hardware Installation and Maintenance Guide for SG5700 Appliances

Configuring the hardware

Содержание StorageGRID SG5712


























































































Результаты поиска

Содержание StorageGRID SG5712

Отзывы:

Похожие инструкции для StorageGRID SG5712

Бренды по названию

Популярные бренды

NetApp StorageGRID SG5712, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание StorageGRID SG5712

Отзывы:

Похожие инструкции для StorageGRID SG5712

Бренды по названию

Популярные бренды