NetApp StorageGRID SG5712 Скачать руководство пользователя | Manualshive

Страница: 51 / 89

background image

https://E2800_Controller_IP

The log in page for SANtricity System Manager appears.

2. Enter the administrator password.

3. Click Cancel to close the Set Up wizard and to display the SANtricity System Manager home

page.

4. Configure hardware alerts.

a. Select Help to access the online help for SANtricity System Manager.

b. Use the Settings > Alerts section of the online help to learn about alerts.

c. Follow the "How To" instructions to set up email alerts, SNMP alerts, or syslog alerts.

5. Manage AutoSupport for the appliance hardware.

a. Select Help to access the online help for SANtricity System Manager.

b. Use the Support > Support Center section of the online help to learn about the

AutoSupport feature.

c. Follow the "How To" instructions to manage AutoSupport for the appliance hardware.

6. If the Drive Security feature is enabled for the appliance and FDE or FIPS drives are installed,

create and manage the security key.

a. Select Help to access the online help for SANtricity System Manager.

b. Use the Settings > System > Security key management section of the online help to learn

about Drive Security.

c. Follow the "How To" instructions to create and manage the security key.

Attention: The E2800 controller acts as a simplex
controller. The security key needed to unlock the
drives is saved to the E2800 controller but not to the
E5700SG controller. You must be able to locate your
key identifier, pass phrase, and the downloaded key
file in case the E2800 controller fails and needs to be
replaced.

7. Optionally, change the administrator password.

a. Select Help to access the online help for SANtricity System Manager.

b. Use the Home > Storage array administration section of the online help to learn about

the administrator password.

c. Follow the "How To" instructions to change the password.

Reviewing the hardware status in SANtricity System Manager

You can use SANtricity System Manager to monitor and manage the individual hardware
components in the appliance and to review hardware diagnostic and environmental information,
such as component temperatures, as well as issues related to the drives.

Steps

1. Open a web browser on a management client, and enter the URL for SANtricity System

Manager:

https://E2800_Controller_IP

The log in page for SANtricity System Manager appears.

2. Enter the administrator password.

3. Click Cancel to close the Set Up wizard and to display the SANtricity System Manager home

page.
The SANtricity System Manager home page appears. In SANtricity System Manager, the
appliance is referred to as a

storage array.

Hardware Installation and Maintenance Guide for SG5700 Appliances

51

Configuring the hardware

«
...
49
50
51
52
53
...
»

Содержание StorageGRID SG5712


























































































Отзывы:

Нет отзывов

Похожие инструкции для StorageGRID SG5712

SR8800 IM-FW-II

Бренд: H3C Страницы: 107

Бренд: 3Com Страницы: 12

Бренд: H3C Страницы: 16

H3C S3600 Series

Бренд: H3C Страницы: 10

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 2

H3C S7500E Series

Бренд: H3C Страницы: 34

Бренд: H3C Страницы: 33

Бренд: H3C Страницы: 14

Бренд: H3C Страницы: 56

H3C S7500E Series

Бренд: H3C Страницы: 112

Бренд: H3C Страницы: 15

SR8800 IM-FW-II

Бренд: H3C Страницы: 5

H3C S7500E Series

Бренд: H3C Страницы: 50

Бренд: H3C Страницы: 37

Бренд: H3C Страницы: 4

Бренд: H3C Страницы: 5

Бренд: H3C Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды