NetApp StorageGRID SG5712 Скачать руководство пользователя

Страница: 77 / 89

b. Click Reboot Controller.

During the reboot, the following screen appears:

The appliance reboots and rejoins the grid. This process can take up to 20 minutes.

c. On the Nodes page, verify that the appliance node returns to the expected status by viewing

the icon to the left of the node name.

When the reboot is complete, the Tasks tab looks like the following screenshot:

9. From SANtricity System Manager, confirm that the new controller is Optimal, and collect

support data.

Related information

NetApp E-Series Systems Documentation Center

Hardware Installation and Maintenance Guide for SG5700 Appliances

Maintaining the SG5700 appliance

Содержание StorageGRID SG5712


























































































Результаты поиска

Содержание StorageGRID SG5712

Отзывы:

Похожие инструкции для StorageGRID SG5712

Бренды по названию

Популярные бренды

NetApp StorageGRID SG5712, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание StorageGRID SG5712

Отзывы:

Похожие инструкции для StorageGRID SG5712

Бренды по названию

Популярные бренды