NetApp StorageGRID SG5712 Скачать руководство пользователя

Страница: 70 / 89

b. Click Reboot Controller.

During the reboot, the following screen appears:

The appliance reboots and rejoins the grid. This process can take up to 20 minutes.

c. On the Nodes page, verify that the appliance node returns to the expected status by viewing

the icon to the left of the node name.

When the reboot is complete, the Tasks tab looks like the following screenshot:

Replacing the E2800 controller

You might need to replace the E2800 controller if it is not functioning optimally or if it has failed.

Before you begin

•

You have a replacement controller with the same part number as the controller you are
replacing.

•

You have downloaded the instructions for replacing the simplex configuration of a failed
E2800 controller canister.

Attention: Refer to the E-Series instructions only
when directed or if you need more details to perform

Hardware Installation and Maintenance Guide for SG5700 Appliances

Maintaining the SG5700 appliance

Содержание StorageGRID SG5712


























































































Результаты поиска

Содержание StorageGRID SG5712

Отзывы:

Похожие инструкции для StorageGRID SG5712

Бренды по названию

Популярные бренды

NetApp StorageGRID SG5712, Руководство по установке и обслуживанию оборудования

Результаты поиска

Содержание StorageGRID SG5712

Отзывы:

Похожие инструкции для StorageGRID SG5712

Бренды по названию

Популярные бренды