NetApp StorageGRID SG5712 Скачать руководство пользователя | Manualshive

Страница: 80 / 89

background image

Replacing other hardware components

You might need to replace a controller battery, drive, fan, or power supply, in the StorageGRID
appliance.

About this task

To replace the battery in the E2800 controller, see the instructions in this guide for replacing the
E2800 controller. Those instructions describe how to remove the controller from the appliance,
remove the battery from the controller, install the battery, and replace the controller.

To replace a drive, power-fan canister, fan canister, power canister, or drive drawer in the
appliance, access the E-Series procedures for maintaining E2800 hardware.

Model

FRU

See E-Series instructions for

SG5712

Drive

Replacing a drive in E2800 12-drive or 24-drive
shelves

Power-fan canister

Replacing a power-fan canister in E2800 shelves

SG5760

Drive

Replacing a drive in E2860 shelves

Power canister

Replacing a power canister in E2860 shelves

Fan canister

Replacing a fan canister in E2860 shelves

Drive drawer

Replacing a drive drawer in E2860 shelves

Related tasks

Replacing the E2800 controller

You might need to replace the E2800 controller if it is not functioning optimally or if it has failed.

Related information

NetApp E-Series Systems Documentation Center

Changing the link configuration of the E5700SG controller

You can change the Ethernet link configuration of the E5700SG controller. You can change the
port bond mode, the network bond mode, and the link speed.

Before you begin

•

You must have the Maintenance or Root Access permission. For details, see the instructions for
administering StorageGRID.

•

You must be signed in to the Grid Manager using a supported browser.

About this task

Options for changing the Ethernet link configuration of the E5700SG controller include:

•

Changing Port bond mode from Fixed to Aggregate, or from Aggregate to Fixed

•

Changing Network bond mode from Active-Backup to LACP, or from LACP to Active-
Backup

•

Enabling or disabling VLAN tagging, or changing the value of a VLAN tag

•

Changing the link speed from 10-GbE to 25-GbE, or from 25-GbE to 10-GbE

Before changing the link configuration, you must place the E5700SG controller into maintenance
mode. Before changing the link configuration, you must place the E5700SG controller controller
into maintenance mode. Putting a StorageGRID appliance into maintenance mode might make the
appliance unavailable for remote access.

Hardware Installation and Maintenance Guide for SG5700 Appliances

80

Maintaining the SG5700 appliance

«
...
78
79
80
81
82
...
»

Содержание StorageGRID SG5712


























































































Отзывы:

Нет отзывов

Похожие инструкции для StorageGRID SG5712

Бренд: 3Com Страницы: 20

Бренд: Paradyne Страницы: 22

Бренд: Patton electronics Страницы: 2

Бренд: Patton electronics Страницы: 86

Бренд: JB Systems Страницы: 24

Бренд: JB Systems Страницы: 61

WS-650 lite Series

Бренд: Laurell Страницы: 84

Бренд: Pakedge Device & Software Страницы: 20

RouterBOARD Groove

Бренд: MikroTik Страницы: 4

Бренд: Moxa Technologies Страницы: 2

Бренд: ADS Technologies Страницы: 1

Бренд: ICP DAS USA Страницы: 8

Бренд: Glacier Страницы: 2

Converter Board R0E521237CFK00

Бренд: Renesas Страницы: 6

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

DiamondLink 3201

Бренд: Patton Страницы: 12

Ezi-SERVOII EtherCAT TO

Бренд: Fastech Страницы: 108

Бренд: Global411 Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды