manualshive.com logo in svg

NetApp StorageGRID SG5712, Руководство по установке и обслуживанию оборудования, Страница: 26 / 89

Поделиться
Скачать
NetApp StorageGRID SG5712 Скачать руководство пользователя страница 26

Viewing boot-up status codes

The seven-segment displays on each controller show status and error codes as the appliance
powers up.

About this task

The E2800 controller and the E5700SG controller display different statuses and error codes.

To understand what these codes mean, see the following resources:

Controller

Reference

E2800 controller

E5700 and E2800 System Monitoring Guide

Note: The codes listed for the E-Series E5700 controller do not apply to the E5700SG
controller in the appliance.

E5700SG controller

"Status indicators on the E5700SG controller"

Steps

1. During boot-up, monitor progress by viewing the codes shown on the seven-segment displays.

•

The seven-segment display on the E2800 controller shows the repeating sequence OS, Sd,

blank

 to indicate that it is performing start-of-day processing.

•

The seven-segment display on the E5700SG controller shows a sequence of codes, ending
with AA and FF.

2. After the controllers have booted up, confirm the seven-segment displays show the following:

Controller

Seven-segment display

E2800 controller

Shows 99, which is the default ID for an E-Series controller shelf.

Hardware Installation and Maintenance Guide for SG5700 Appliances 

26

Installing the hardware

Содержание StorageGRID SG5712


























































































Отзывы:

Нет отзывов