manualshive.com logo in svg

NEC Express5800/53La, Руководство пользователя, Страница: 89 / 314

Поделиться
Скачать
NEC Express5800/53La Скачать руководство пользователя страница 89

Configuring Your Workstation    4-17

Onboard Video Controller

Option

Parameter

Description

Your Setting

Pre-Allocated
Memory Size

[32MB]
64MB
128MB

Specify the memory size to be used by
the onboard graphics accelerator.

[   ]: Factory-set

Onboard LAN

Option

Parameter

Description

Your Setting

LAN Controller

[Enabled]
Disabled

Enables or disables the onboard LAN
controller.

Option ROM Scan

[Disabled]
Enabled

Enables or disables PXE Boot by the
onboard LAN controller.
Set to "Enabled" to boot the system
from the device on network connected
with the network port of the
workstation.
Set to "Disabled" to re-setup the
workstation.
Set to "Disabled" if the option board is
installed and the hard disk drive
containing the bootable OS is
connected.

[   ]: Factory-set

Содержание Express5800/53La



























































































































































































































































































































Отзывы:

Нет отзывов