NEC Express5800/53La Скачать руководство пользователя страница 208 | Manualshive

Страница: 208 / 314

NEC Express5800/53La Скачать руководство пользователя страница 208

8-14 Troubleshooting

There are some cases that the following event logs are registered during the Windows XP
installation.

Event Source: WinMgmt

Event ID:

5603

→

It is not a problem in operating the system.

Event Source: DCOM

Event ID:

10016

→

It is not a problem in operating the system.

Event Source: WinMgmt

Event ID:

63

→

It is not a problem in operating the system.

The system displays the message below and fails to log on.

Windows Product Activation

This copy of Windows must be activated with Microsoft before you can
continue. You cannot log on until you activate Windows.

To shut down the computer, click Cancel.

YES

NO

Cancel

→

In Windows XP, the above message will be displayed if you use the operating
system without executing the license authentication. Select "Yes", and execute the
procedure for license authentication.

Cannot install the operating system correctly.

Did you confirm the notes on installing the operating system?

→

See Chapter 6.

During installation, the following warning is registered in the System Log of the Event Viewer:

Error detected on the device \Device\CdRom0
during the paging operation.

→

There is no problem on this issue.

«
...
206
207
208
209
210
...
»

Содержание Express5800/53La



























































































































































































































































































































Отзывы:

Нет отзывов