NEC Express5800/53La Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 314

NEC Express5800/53La Скачать руководство пользователя страница 194

7-16 Maintenance

RELOCATING/STORING THE WORKSTATION

Follow the procedure below to relocate or store the workstation:

CAUTION

Observe the following instructions to use the workstation safely. Failure to
follow these instructions may cause a fire, personal injury, or property
damage. See pages 1-3 to 1-10 for details.

■

Do not install the workstation in any place other than specified.

■

Do not connect any grounding line with the power cord of the workstation
plugged to a power source.

■

Do not connect/disconnect any interface cable with the power cord of the
workstation plugged to a power source.

■

Do not use any other interface cable than authorized by NEC.

IMPORTANT:

If the workstation needs to be relocated/stored due to a change in
the floor layout to a great extent, contact your service
representative.

Make sure to make a backup copy of your valuable data in the hard
disk drive, if any.

Make sure not to apply a shock to hard disk drives to relocate the
workstation if the contains any.

1.

Take a media out of the workstation, if any.

2.

Power off the workstation (the POWER/SLEEP lamp goes off).

3.

Unplug the power cord of the workstation from a power outlet.

4.

Remove all the cables from the workstation.

5.

Protect the workstation with the shock-absorbing materials, and pack it securely.

IMPORTANT:

If you use the workstation after transported or relocated,

check the system timer and adjust it if necessary. If the system timer
advances or delays remarkably with the passage of time, contact your
service representative to repair it.
The workstation or internal option device may be dewed if it is brought
to a warm place from a cold place suddenly. Using a workstation or an
internal device with dew attached may cause malfunction or failure.
Make sure to adapt them to the operating environment before using
them.

«
...
192
193
194
195
196
...
»

Содержание Express5800/53La



























































































































































































































































































































Отзывы:

Нет отзывов