NEC Express5800/53La Скачать руководство пользователя страница 209 | Manualshive

Страница: 209 / 314

NEC Express5800/53La Скачать руководство пользователя страница 209

Troubleshooting 8-15

Fail to start the OS:

Is the NEC EXPRESSBUILDER DVD in the optical disk drive?

→

Take out the NEC EXPRESSBUILDER DVD and restart the workstation.

Is the OS broken?

→

Use recovery process to recover the system. (See "Recovery for Windows System"
in this chapter.)

The OS presents unstable operation:

Did you update the system?

→

Installing a network drive after installation of the OS may cause unstable
operation. Use the NEC EXPRESSBUILDER DVD to update the system. (See
Chapter 6.)

The system does not restart automatically when a stop error occurs, though the system is
adjusted to automatically restarting:

→

When the system does not restart automatically, restart it manually.

The system restarts automatically when a stop error occurs, though the system is NOT
adjusted to automatically restarting:

→

There is no problem about this issue.
Check the System Event Log to confirm that STOP error occurred.

Cannot turn the power OFF at the blue screen:

→

If you want to turn off the power at the blue screen, execute forced shutdown
(forced shutdown: continue to press POWER/SLEEP switch for 4 seconds). The
power will not be turned off if you press the switch for less than 3 seconds.

«
...
207
208
209
210
211
...
»

Содержание Express5800/53La



























































































































































































































































































































Отзывы:

Нет отзывов