NEC Express5800/53La Скачать руководство пользователя страница 180 | Manualshive

Страница: 180 / 314

NEC Express5800/53La Скачать руководство пользователя страница 180

7-2 Maintenance

CLEANING

Clean the workstation on a regular basis to keep the workstation in a good shape.

WARNING

Observe the following instructions to use the workstation safely. Failure to
follow these instructions may result in death or serious personal injury. See
pages 1-3 to 1-10 for details.

■

Do not disassemble, repair, or alter the workstation.

■

Do not remove the lithium battery.

■

Disconnect the power plug before working with the workstation.

■

Do not connect any grounding line with the power cord of the workstation
plugged to a power source.

■

Do not look into the optical disk drive.

CAUTION

Observe the following instructions to use the workstation safely. Failure to
follow these instructions may cause a fire, personal injury, or property
damage. See pages 1-3 to 1-10 for details.

■

Avoid installation in extreme temperature conditions.

«
...
178
179
180
181
182
...
»

Содержание Express5800/53La



























































































































































































































































































































Отзывы:

Нет отзывов