NEC Express5800/53La Скачать руководство пользователя страница 179 | Manualshive

Страница: 179 / 314

NEC Express5800/53La Скачать руководство пользователя страница 179

Chapter 7

Maintenance

This chapter describes the daily maintenance of the workstation and precautions when relocating or
storing the workstation.

MAKING BACKUP COPIES

NEC recommends you make backup copies of your valuable data stored in hard disk drives of the
workstation on a regular basis. For backup storage devices suitable for the workstation and backup
tools, consult with your service representative.

When you have changed the hardware configuration or BIOS configuration, select "System
Information Management" and then "Save" of the NEC EXPRESSBUILDER to make a backup
copy of the system information.

Also make a backup copy of the disk array configuration data if your system is in the array
configuration. When your hard disk drives have been auto-rebuilt due to a failure, it is
recommended to make a backup copy of the configuration data. To make a backup copy of the
configuration data, use the configuration utility that is resident in the FLASH memory on the
optional disk array controller board. Refer to the manual supplied with the board.

«
...
177
178
179
180
181
...
»

Содержание Express5800/53La



























































































































































































































































































































Отзывы:

Нет отзывов