NEC Express5800/53La Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 314

NEC Express5800/53La Скачать руководство пользователя страница 60

3-4 Setting Up Your Workstation

SELECTING A SITE

Read the following precautions before selecting a suitable site for your workstation. The following
describes installation of the workstation and connections to the workstation.

CAUTION

Observe the following instructions to use the workstation safely. Failure to
follow these instructions may cause a fire, personal injury, or property damage.
See pages 1-3 to 1-10 for details.

■

Do not hold the front mask when carrying the workstation.

■

Do not install the workstation in any place other than specified.

■

Do not hold the air duct when lifting the workstation.

The following figure illustrates a site suitable for installing the workstation.

* It is recommended that the workstation should be used in a

room where temperature is in the range between 15 to 25ºC.

Clean and tidy room

Grounded parallel bi-

polar power outlet

Close enough to connect
the mouse and the display
unit.

Install the
workstation on the
rigid, flat desk.

Allow clearance of at least
150 mm in front of and
behind the workstation.

Environmental requirements for operation

<Operating>

<Halting>

Temperature:

10 to 35ºC

5 to 40ºC

Humidity:

20 to 80%

10 to 80%

Temperature gradient:

±

10ºC/h

±

15ºC/h

Atmosphere:

749 to 1040 hpa

749 to 1040 hpa

«
...
58
59
60
61
62
...
»

Содержание Express5800/53La



























































































































































































































































































































Отзывы:

Нет отзывов