NEC Express5800/53La Скачать руководство пользователя страница 62

Страница: 62 / 314

3-6 Setting Up Your Workstation

PREPARATION FOR INSTALLATION

With Vertical Installation

When you want to install the workstation vertically, first remove the stabilizers from bottom of the
workstation to place the workstation vertically.

You need to install the air duct on top of the workstation to keep the cooling effect in the
workstation.

Installing Air Duct

IMPORTANT:

To keep the cooling effect in the workstation, the air

duct must be installed. In addition, do not install the workstation with
the air holes being covered with the wall or the like.

Hooks on air duct

(4 places)

Engage hooks (4 places) with the slots on
the workstation, and insert them.

Содержание Express5800/53La



























































































































































































































































































































Результаты поиска

Содержание Express5800/53La

Отзывы:

NEC Express5800/53La, Руководство пользователя, Страница: 62 / 314

Результаты поиска

Содержание Express5800/53La

Отзывы: