NEC Express5800/53La Скачать руководство пользователя страница 187

Страница: 187 / 314

Maintenance 7-9

MAINTENANCE TOOLS

The Maintenance Tools is a tool of this product prevention to maintain, and to analyze the trouble.

IMPORTANT:

This guide contains procedures to use a floppy disk,

however, your workstation is not equipped with factory-installed floppy
disk drive. Use the optional Flash FDD or USB FDD.

Starting Maintenance Tools

The Maintenance Tools is started according to the following procedure.

Turn on peripheral devices and the workstation in this order.

Insert the NEC EXPRESSBUILDER DVD supplied with your workstation into the optical
disk drive of your workstation.

Press

Ctrl

Alt

, and

Delete

to reboot the workstation from the NEC EXPRESSBUILDER.

(You may also turn off and then on again to reboot the workstation.)

System boots up displaying Boot selection menu.

IMPORTANT:

An initial selection of the menu is "Os installation".

"Os installation" starts by the automatic after the Boot selection menu is
displayed.

Содержание Express5800/53La



























































































































































































































































































































Результаты поиска

Содержание Express5800/53La

Отзывы:

NEC Express5800/53La, Руководство пользователя, Страница: 187 / 314

Результаты поиска

Содержание Express5800/53La

Отзывы: