NEC Express 5800/R320c-E4 Скачать руководство пользователя страница 6

Страница: 6 / 177

Notations Used in This Document

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows Server 2008)

Abbreviations of Operating Systems (Windows)

Windows Operating Systems are referred to as follows.

Refer to

Chapter 1

(

1.2 Supported Windows OS)

Installation Guide (Windows)

for detailed

information.

Notations in this document

Official names of Windows

Windows Server 2008 R2

Windows Server 2008 R2 Standard
Windows Server 2008 R2 Enterprise

POST

POST described in this document refer to the following.

•

Power On Self-Test

BMC

BMC described in this document refer to the following.

•

Baseboard Management Controller

Содержание Express 5800/R320c-E4


















































































































































































Результаты поиска

Содержание Express 5800/R320c-E4

Отзывы:

Похожие инструкции для Express 5800/R320c-E4

Бренды по названию

Популярные бренды

NEC Express 5800/R320c-E4, Руководство по установке

Результаты поиска

Содержание Express 5800/R320c-E4

Отзывы:

Похожие инструкции для Express 5800/R320c-E4

Бренды по названию

Популярные бренды