NEC Express 5800/R320c-E4 Скачать руководство пользователя страница 128

Страница: 128 / 177

1. Bundled Software for the Server

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows Server 2008)

128

Chapter 2 Installing Bundled Software

1.5.2

Preparing for the Active Upgrade Process

Preparing for the Active Upgrade process involves the following tasks:

1. Learning about the prerequisites for your Express5800/ft series system.

–

Software Upgrade Support

–

Prerequisites

–

Recommendations

2. If necessary, plan for the brief downtime associated with restarting your applications while merging the

system.

–

Managing Applications during the Upgrade Process

3. Configure Remote Desktop Connection if necessary.

Either one of remote desktop connection or remote KVM must be enabled so that the Production Side
can communicate with Upgrade Side during upgrade.

–

Configuring Remote Desktop Connection

4. Verify the prerequisites to use Remote KVM Console and configure if required.

Either one of remote desktop connection or remote KVM must be enabled so that the Production Side
can communicate with Upgrade Side during upgrade.

–

Configuring Remote KVM Console

5. Prepare the IP address to allocate to the Upgrade Side’s system.

–

Preparing an IP address to assign to the Upgrade Side

6. Install the Active Upgrade Console

–

Installing the Active Upgrade Console

7. If necessary, enable the exception for Active Upgrade Console in Windows Firewall properties

–

Configuring Windows Firewall for the Active Upgrade Process

8. If necessary, copy any required software installation packages to the system.

–

Copying Software Upgrade Packages to the System

9. Verify if your system is prepared for Active Upgrade process.

–

Verifying preparation

10. When you are finished preparing for the upgrade, start the Active Upgrade Console.

–

Starting and Exiting the Active Upgrade Console

Содержание Express 5800/R320c-E4


















































































































































































Результаты поиска

Содержание Express 5800/R320c-E4

Отзывы:

Похожие инструкции для Express 5800/R320c-E4

Бренды по названию

Популярные бренды

NEC Express 5800/R320c-E4, Руководство по установке

Результаты поиска

Содержание Express 5800/R320c-E4

Отзывы:

Похожие инструкции для Express 5800/R320c-E4

Бренды по названию

Популярные бренды