NEC Express 5800/R320c-E4 Скачать руководство пользователя страница 66

Страница: 66 / 177

3. Setting Up Windows Server 2008 R2

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows Server 2008)

Chapter 1 Installing OS

On the following screen, make sure that the

Starter Pack

option is selected, and then click

Install

Tips

If Starter Pack is already installed, the

ft Server Control Software

is selected by

default. To install Starter Pack again, select the

Starter Pack

4. Read the message, and then click

Starter Pack installation starts.

5. The following message appears when Starter Pack installation is complete.

Follow the instructions in the message, and remove EXPRESSBUILDER DVD.

6. Click

to restart the system.

Installation of Starter Pack is now complete.

Содержание Express 5800/R320c-E4


















































































































































































Результаты поиска

Содержание Express 5800/R320c-E4

Отзывы:

Похожие инструкции для Express 5800/R320c-E4

Бренды по названию

Популярные бренды

NEC Express 5800/R320c-E4, Руководство по установке

Результаты поиска

Содержание Express 5800/R320c-E4

Отзывы:

Похожие инструкции для Express 5800/R320c-E4

Бренды по названию

Популярные бренды