NEC Express 5800/R320c-E4 Скачать руководство пользователя

Страница: 89 / 177

3. Setting Up Windows Server 2008 R2

Express5800/R320c-E4, R320c-M4, R320d-E4, R320d-M4 Installation Guide (Windows Server 2008)

Chapter 1 Installing OS

Important

•

If the system is rebooted during synchronization, the process cannot be

completed. Do not restart the system until the synchronization is completed.

•

When the system is halted without shutting down Windows properly due to

forced shutdown or others, the entire area of the partition on the synchronized

disks will be resynchronized after the system is restarted.

Synchronization completed

DISK ACCESS LED

RDR Utility

Op State: State

Status

Source disk

Green (Blinking)

Online

–

Destination disk

Green (Blinking)

Online

–

RDR Virtual Disk

–

Duplex

None

Tips

DISK ACCESS LED is lit green only when hard disk drive is accessed.

If no access is made, the LED seems to be unlit.

Содержание Express 5800/R320c-E4


















































































































































































Результаты поиска

Содержание Express 5800/R320c-E4

Отзывы:

Похожие инструкции для Express 5800/R320c-E4

Бренды по названию

Популярные бренды

NEC Express 5800/R320c-E4, Руководство по установке

Результаты поиска

Содержание Express 5800/R320c-E4

Отзывы:

Похожие инструкции для Express 5800/R320c-E4

Бренды по названию

Популярные бренды