Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-56

The following section illustrates how to use these ports to set up different applications.

Sample Applications of VLANs using the EDS-508A/505A

Port 3 (Trunk Port, PVID 1)

VLAN 5 Untagged Device

VLAN 3 Untagged
Device

VLAN 4 Untagged
Device

VLAN 5 Untagged Device

VLAN 2 Untagged
Device

VLAN 4 Tagged Device, VID 4

VLAN 3 Tagged Device, VID 3

VLAN 2 Untagged
Device

VLAN 2 Untagged
Device

Device A

Switch A

Switch B

Device C

Device B

Device D

Device E

Device F

Device G

Device H

Device I

Port 1 (Access Port
PVID 5)

Port 7 (Access Port
PVID 4)

Port 5 (Access Port

PVID 3)

Port 4 (Access
Port PVID 2)

Port 2 (Trunk Port PVID 2,
Fixed VLAN (Tagged)=3,4)

Port 6 (Access Port PVID 5)

HUB

In this application,



Port 1 connects a single untagged device and assigns it to VLAN 5; it should be configured as

“Access Port” with PVID 5.



Port 2 connects a LAN with two untagged devices belonging to VLAN 2. One tagged device
with VID 3 and one tagged device with VID 4. It should be configured as “Trunk Port” with
PVID 2 for untagged device and Fixed VLAN (Tagged) with 3 and 4 for tagged device. Since
each port can only have one unique PVID, all untagged devices on the same port can only
belong to the same VLAN.



Port 3 connects with another switch. It should be configured as “Trunk Port.” GVRP protocol
will be used through the Trunk Port.



Port 4 connects a single untagged device and assigns it to VLAN 2; it should be configured as
“Access Port” with PVID 2.



Port 5 connects a single untagged device and assigns it to VLAN 3; it should be configured as
“Access Port” with PVID 3.



Port 6 connect a single untagged device and assigns it to VLAN 5; it should be configured as
“Access Port” with PVID 5.



Port 7 connects a single untagged device and assigns it to VLAN 4; it should be configured as
“Access Port” with PVID 4.

«
...
69
70
71
72
73
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

Бренд: ICP DAS USA Страницы: 14

Бренд: ICP DAS USA Страницы: 25

Бренд: ICP DAS USA Страницы: 15

Бренд: ICP DAS USA Страницы: 8

Бренд: ICP Страницы: 14

Бренд: DAQ system Страницы: 41

Бренд: DAQ system Страницы: 19

CompactPCI CC8-BLUES

Бренд: EKF Electronik Страницы: 52

Fieldpoint cFP-RTD-124

Бренд: National Instruments Страницы: 15

Бренд: Garland Страницы: 43

Procont LMC-008-IO

Бренд: janitza Страницы: 28

Hotwire ATM Line Cards 8335

Бренд: Paradyne Страницы: 132

Бренд: Glacier Страницы: 2

Бренд: Cypress Semiconductor Страницы: 33

Бренд: LevelOne Страницы: 3

Бренд: Acromag Страницы: 35

Бренд: Raven Страницы: 33

Бренд: SMC Networks Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды