Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 50

Страница: 50 / 129

EDS-508A/505A Series User’s Manual

Featured Functions

3-35

Ring 1/2—2nd Ring Port Status

The “Ports Status” indicators show

Forwarding

for normal transmission,

Blocking

if this port is

connected to a backup path and the path is blocked, and

Link down

if there is no connection.

Coupling—Mode

Indicates either

None

Dual Homing

, or

Ring Coupling

Coupling—Coupling Port status

Indicates either

Primary

, or

Backup

Explanation of “Settings” Items

Redundancy Protocol

Setting

Description

Factory Default

Turbo Ring

Select this item to change to the
Turbo Ring configuration page.

Turbo Ring V2

Select this item to change to the
Turbo Ring V2 configuration page.

Turbo Chain

Select this item to change to the
Turbo Chain configuration page

RSTP (IEEE
802.1W/1D)

Select this item to change to the
RSTP configuration page.

None

Ring redundancy is not active

None

Enable Ring 1

Setting

Description

Factory Default

Enabled

Enable the Ring 1 settings

Disabled

Disable the Ring 1 settings

Not checked

Enable Ring 2*

Setting

Description

Factory Default

Enabled

Enable the Ring 2 settings

Disabled

Disable the Ring 2 settings

Not checked

*You should enable both Ring 1 and Ring 2 when using the Dual-Ring architecture.

Set as Master

Setting

Description

Factory Default

Enabled

Select this EDS as Master

Disabled

Do not select this EDS as Master

Not checked

Redundant Ports

Setting

Description

Factory Default

1st Port

Select any port of the EDS to be
one of the redundant ports.

EDS-505A: port 4
EDS-508A: port 7

2nd Port

Select any port of the EDS to be
one of the redundant ports.

EDS-505A: port 5
EDS-508A: port 8

Enable Ring Coupling

Содержание EDS-505A Series


































































































































Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды

Moxa Technologies EDS-505A Series, Руководство пользователя

Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды