Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-37

Moxa’s Turbo Chain is an advanced software-technology that gives network administrators the
flexibility of constructing any type of redundant network topology. When using the “chain”
concept, you first connect the Ethernet switches in a chain and then simply link the two ends of the
chain to an Ethernet network, as illustrated in the following figure.

Turbo Chain can be used on industrial networks that have a complex topology. If the industrial
network uses a multi-ring architecture, Turbo Chain can be used to create flexible and scalable
topologies with a fast media-recovery time.

Setup Turbo Chain

1.

Select the Head switch, Tail switch, and Member switches.

2.

Configure one port as the Head port and one port as the Member port in the Head switch,
configure one port as the Tail port and one port as the Member port in the Tail switch, and
configure two ports as Member ports in each of the Member switches.

3.

Connect the Head switch, Tail switch, and Member switches as shown in the diagram.

The path connecting to the Head port is the main path, and the path connecting to the Tail port is
the back up path of the Turbo Chain. Under normal conditions, packets are transmitted through the
Head Port to the LAN Network. If any Turbo Chain path is disconnected, the Tail Port will be
activated to continue packet transmission.

Configuring “Turbo Chain”

«
...
50
51
52
53
54
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

MatrixPRO-II DVI 16x16

Бренд: Barco Страницы: 43

Бренд: Barco Страницы: 5

Бренд: F5 Страницы: 2

Бренд: F5 Страницы: 90

Бренд: F5 Страницы: 47

DGE-560T - Gigabit PCI-Express SNMP VLAN Flow Control Network...

Бренд: D-Link Страницы: 53

Бренд: Teagle Страницы: 40

Бренд: Commell Страницы: 58

Бренд: TP-Link Страницы: 3

EK-FB GA AX370 Gaming RGB Monoblock

Бренд: ekwb Страницы: 2

Бренд: ProCurve Страницы: 2

Бренд: IFM Electronic Страницы: 14

Бренд: Renesas Страницы: 76

PowerMatch ESPLink

Бренд: Bose Страницы: 2

Бренд: Unex Страницы: 27

AlterPath Manager 2500

Бренд: Cyclades Страницы: 368

Бренд: Aaeon Страницы: 100

Бренд: NetComm Wireless Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды