Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 80

Страница: 80 / 129

EDS-508A/505A Series User’s Manual

Featured Functions

3-65

IGMP Table

The EDS displays the current active IGMP groups that were detected.

The information includes

VID

Auto-learned Multicast Router Port

Static Multicast Router

Port

Querier Connected Port

, and the

and

MAC

addresses of active IGMP groups.

Static Multicast MAC

If required, the EDS also supports adding multicast groups manually.

Add New Static Multicast Address to the List

Setting

Description

Factory Default

MAC Address

Input the multicast MAC address of this host.

None

MAC Address

Setting

Description

Factory Default

integer

Input the number of the VLAN to which the host with
this MAC Address belongs.

None

Join Port

Setting

Description

Factory Default

Select/Deselect

Select the appropriate options to select the join ports for
this multicast group.

None

Содержание EDS-505A Series


































































































































Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды

Moxa Technologies EDS-505A Series, Руководство пользователя

Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды