Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-85

Using Monitor

You can monitor statistics in real time from the EDS’s web console and serial console.

Monitor by Switch

Access the Monitor by selecting “System” from the left selection bar. Monitor by System allows
the user to view a graph that shows the combined data transmission activity of all of the EDS’s
ports. Click one of the four options—

Total Packets

,

TX Packets

,

RX Packets

, or

Error

Packets

—to view transmission activity of specific types of packets. Recall that TX Packets are

packets sent out from the EDS, RX Packets are packets received from connected devices, and
Error Packets are packets that did not pass TCP/IP’s error checking algorithm. The Total Packets
option displays a graph that combines TX, RX, and TX Error, RX Error Packets activity. The
graph displays data transmission activity by showing

Packets/s

(i.e., packets per second, or pps)

versus

sec.

(seconds). In fact, three curves are displayed on the same graph:

Unicast

packets (in

red color),

Multicast

packets (in green color), and

Broadcast

packets (in blue color). The graph is

updated every few seconds, allowing the user to analyze data transmission activity in real-time.

«
...
98
99
100
101
102
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

NetDefend DFL-260E

Бренд: D-Link Страницы: 328

ShareCenter Pulse DNS-320

Бренд: D-Link Страницы: 2

DFL-210 - NetDefend - Security Appliance

Бренд: D-Link Страницы: 19

Бренд: D-Link Страницы: 22

Бренд: D-Link Страницы: 4

Бренд: Dahua Страницы: 12

NetDefend DFL-1600

Бренд: D-Link Страницы: 23

ARM Cortex-A9 MPCore

Бренд: Dave Embedded Systems Страницы: 67

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Бренд: STONEFLY Страницы: 48

Бренд: Oracle Страницы: 24

Бренд: Freescale Semiconductor Страницы: 921

Бренд: Genie Страницы: 15

Бренд: M86 Security Страницы: 309

Бренд: TP-Link Страницы: 2

Бренд: ZALMAN Страницы: 7

Octopus G Series

Бренд: TwinMOS Страницы: 29

Бренд: Uniflair Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды