Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 13

Страница: 13 / 129

EDS-508A/505A Series User’s Manual

Getting Started

2-6

Perform the following steps to access the console utility by Telnet.

Click

Start



Run

, and then telnet to the EDS’s IP address from the Windows

Run

window.

(You may also issue the telnet command from the MS-DOS prompt.)

Type

to choose

ansi/vt100

, and then press

Enter

The Console login screen will appear. Press

Enter

to open the Account pop-up selector and

then select either

admin

user

. Use the keyboard’s down arrow to move the cursor to the

Password field, enter the

Console Password

(this is the same as the Web Browser password;

leave the

Password

field blank if a console password has not been set), and then press

Enter

When the

Main Menu

of the EDS’s console utility opens, click

Terminal



references…

from the menu at the top of the window.

When the

Terminal Preferences

window opens, make sure that the

VT100 Arrows

option is

selected.

NOTE

The Telnet Console looks and operates in precisely the same manner as the RS-232 Console.

Содержание EDS-505A Series


































































































































Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды

Moxa Technologies EDS-505A Series, Руководство пользователя

Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды