Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 87

Страница: 87 / 129

EDS-508A/505A Series User’s Manual

Featured Functions

3-72

Local User Database Setup

When setting the Local User Database as the authentication database, set the database first.

Local User Database Setup

Setting

Description

Factory Default

User Name
(Max. 30 characters)

User Name for Local User Database

None

Password
(Max. 16 characters)

Password for Local User Database

None

Description
(Max. 30 characters)

Description for Local User Database

None

NOTE

The user name for the Local User Database is case-insensitive.

Port Access Control Table

The port status will indicate whether the access is authorized or unauthorized.

Содержание EDS-505A Series


































































































































Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды

Moxa Technologies EDS-505A Series, Руководство пользователя

Результаты поиска

Содержание EDS-505A Series

Отзывы:

Похожие инструкции для EDS-505A Series

Бренды по названию

Популярные бренды