Moxa Technologies EDS-505A Series Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 129

background image

EDS-508A/505A Series User’s Manual

Featured Functions

3-24

User Auth. Type (for SNMP V1, V2c, V3 and V3 only)

Setting

Description

Factory Default

No-Auth

Use admin account or user account to
access objects. No authentication.

No

MD5-Auth

Provides authentication based on the
HMAC-MD5 algorithms. 8-character
passwords are the minimum requirement
for authentication.

No

SHA-Auth

Provides authentication based on the
HMAC-SHA algorithms. 8-character
passwords are the minimum requirement
for authentication.

No

User Data Encryption Key (for SNMP V1, V2c, V3 and V3 only)

Setting

Description

Factory Default

Enable

8-character data encryption key is the
minimum requirement for data encryption
(maximum of 30 characters)

No

Disable

No data encryption

No

Trap Settings

SNMP traps allow an SNMP agent to notify the NMS of a significant event. The EDS-508A/505A
supports two SNMP modes,

Trap

mode and

Inform

mode.

SNMP Trap Mode

In

Trap

mode, the SNMP agent sends an SNMPv1 trap PDU to the NMS. No acknowledgment is

sent back from the NMS so the agent has no way of knowing if the trap reached the NMS.

SNMP Inform Mode

SNMPv2 provides an inform mechanism. When an inform message is sent from the SNMP agent
to the NMS, the receiver sends a response to the sender acknowledging receipt of the event. This
behavior is similar to that of the get and set requests. If the SNMP agent doesn’t receive a response
from the NMS for a period of time, the agent will resend the trap to the NMS agent. The maximum
timeout time is 300 secs (default is 1 sec), and the maximum number of retries is 99 times (default
is 1 time). When the SNMP agent receives acknowledgement from the NMS, it will stop resending
the inform messages.

«
...
37
38
39
40
41
...
»

Содержание EDS-505A Series


































































































































Отзывы:

Нет отзывов

Похожие инструкции для EDS-505A Series

Бренд: H3C Страницы: 21

ER3-100 (5K02-55)

Бренд: 8e6 Technologies Страницы: 74

Бренд: Abocom Страницы: 1

Бренд: Watchguard Страницы: 40

Бренд: Cypress Semiconductor Страницы: 10

Barricade SMC7901WBRA2

Бренд: SMC Networks Страницы: 2

Anybus Communicator ABC4021

Бренд: HMS Networks Страницы: 60

Бренд: Zonet Страницы: 53

OP-8000-EDFA-1U Series

Бренд: Optostar Страницы: 9

EK-Quantum Momentum ROG Rampage VI Encore

Бренд: EK Страницы: 11

Бренд: Teletronics International Страницы: 57

Бренд: Asante Страницы: 150

Бренд: Giacomini Страницы: 2

Бренд: Z3 Technology Страницы: 67

Slideaway CL1008

Бренд: ATEN Страницы: 77

Бренд: Variscite Страницы: 17

KÜHLER H2O 920

Бренд: Antec Страницы: 6

IA611 Xplained Pro

Бренд: Knowles Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды